Qnap [ Ubiquiti UniFi ] Wi-Fi Management

Gaudi a dit:
oyasama a dit:
Hello, does not start after upgrading QTS firmware to 4.5.1

Best regards :)
Try to start the app from a SSH session and check if any error messages appear?

Can you please tell me what the command would be to run unifi by console? I don't usually fret much with putty in the qnap, I'm sorry. Thank you. Best regards :rolleyes:
 
oyasama a dit:
Gaudi a dit:
oyasama a dit:
Hello, does not start after upgrading QTS firmware to 4.5.1

Best regards :)
Try to start the app from a SSH session and check if any error messages appear?

Can you please tell me what the command would be to run unifi by console? I don't usually fret much with putty in the qnap, I'm sorry. Thank you. Best regards :rolleyes:

Okay, now I see that with firm 4.5.1 there is an app manager around the console, easier, I'll see if I get any errors from the console. Thanks again. :D
 
oyasama a dit:
oyasama a dit:
Gaudi a dit:
Try to start the app from a SSH session and check if any error messages appear?

Can you please tell me what the command would be to run unifi by console? I don't usually fret much with putty in the qnap, I'm sorry. Thank you. Best regards :rolleyes:

Okay, now I see that with firm 4.5.1 there is an app manager around the console, easier, I'll see if I get any errors from the console. Thanks again. :D

Well, it looks like with the new console app manager in 4.5.1, I've been able to run unifi and it works. The problem may not start with QTS boot after restarting. At least I had restarted the nas 3 times without success. Thanks anyway. :geek:
 
Bonjour

Tout d'abord merci pour ce package.
Je ne sais pas si ce n'est que moi mais impossible de DL ce package (et aucun autre d'ailleurs) car il semble que le certificat SSL du site ne soit plus valide, tout est donc verrouillé et ça peux importe le navigateur
 
impossible de DL ce package
Bizarre j'utilise ce package depuis très longtemps et aucun pb. Je télécharge le package en allant sur le site : https://www.qnapclub.eu/fr/ puis je fait une installation manuel .
Pour les mise à jour il suffit de télécharger la nouvelle version et de l'installer , les réglages du contrôleur ne sont pas perdu . ;)
 
Bah habituellement aussi, mais là si j'essai d'aller DL le package j'ai un message comme quoi le SSL n'est plus certifié, obligé de passer en http pour pouvoir y acceder
 
Hello,
I have just installed latest version on my TS-809 (v 4.2.6), however whenever I start UniFi just a blank page is starting - no content. Any idea what should I do else.
The NAS was just istalled.

Regards

Krzysztof
 
Bonjour,
Comment peut-on accéder le contrôleur Unifi par SSH?
Si le serveur SSH du NAS est activé, c'est a lui qu'on se connecte, et non au contrôleur Unifi, et si le serveur SSH du NAS est désactivé, la connexion est refusée.
Est-ce que l'implantation du contrôleur Unifi dans un .qpkg est faite sur un port différent que le 22 pour le SSH?
 
TcheckCa a dit:
Comment peut-on accéder le contrôleur Unifi par SSH?
Perso je ne vois pas trop l'intérêt . En local je pense que cela doit -être possible ......
Pour ma part j'accède au contrôleur via : myqnapcloud.com :38193 et j'accède ainsi au contrôleur que ce soit en local ou à distance