Bonjour
j ai un problème de démarrage de mon nas : il se plante
je lai connecter par un dongle USB to TTL avec l'interface interne (rx/tx/gnd) j'ai u comme résulta :
lusun:
un petit message dans le code : *** Warning - bad CRC or NAND, using default environment
lien configuration : https://wikidevi.wi-cat.ru/LaCie_2Big_NAS
merci d'avance
j ai un problème de démarrage de mon nas : il se plante
je lai connecter par un dongle USB to TTL avec l'interface interne (rx/tx/gnd) j'ai u comme résulta :
lusun: un petit message dans le code : *** Warning - bad CRC or NAND, using default environment
Code:
▒
_ ____ _
| | __ _ / ___(_) ___
| | / _V | | | |/ _ \
| |__ | (_| | |___| | __/
|____| \__,_|\____|_|\___|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: L2BIG_DDR3 REV: 1 LE
Hold front button - long :
U-Boot 1.1.4 (Mar 21 2012 - 11:02:55) Marvell version: 3.5.9 LaCie 2.0.6
U-Boot code: 06000000 -> 0607FFF0 BSS: -> 060D14C0
Soc: 88F6282 A1CPU running @ 2000Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 20 tRCD=8
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 98M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (98M - 97M): Done
NAND:256 MB
*** Warning - bad CRC or NAND, using default environment
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.
SCSI: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: 64bit ncq pm led clo pmp pio slum part
scanning bus for devices...
Invaild port number 2
Invaild port number 3
Net: egiga0 [PRIME]
egiga0 no link
Waiting for LUMP (3)
no lump receive; continuing
Hit any key to stop autoboot: 0
Reset IDE:
Marvell Serial ATA Adapter
Marvell Serial ATA Adapter
Integrated Sata device found
PCIe SATA:ffffffff
Booting Nexus layout from disk 0...
** Bad partition 3 **
Booting Nexus layout from disk 1...
** Bad partition 3 **
Booting Nexus rescue from NAND...
Loading from NAND 256MB 3,3V 8-bit, offset 0x100000
Reading data from 0x100000 -- 100% complete.
Image Name: Linux-2.6.31.14-svn7170
Created: 2012-04-06 17:10:52 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8755908 Bytes = 8.4 MB
Load Address: 00008000
Entry Point: 00008000
Reading data from 0x959800 -- 100% complete.
## Booting image at 00800000 ...
Image Name: Linux-2.6.31.14-svn7170
Created: 2012-04-06 17:10:52 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8755908 Bytes = 8.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
bootargs from environment variables : button=1 bootfail=1 console=ttyS0,115200 root=/dev/mtdblock2 cap=gpt,lba64
Starting kernel ...
Uncompressing Linux...................................................................................................................................................................................................................................................................................................................................................................... done, booting the kernel.
▒
_ ____ _
| | __ _ / ___(_) ___
| | / _V | | | |/ _ \
| |__ | (_| | |___| | __/
|____| \__,_|\____|_|\___|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: L2BIG_DDR3 REV: 1 LE
Hold front button - long : FAIL
U-Boot 1.1.4 (Mar 21 2012 - 11:02:55) Marvell version: 3.5.9 LaCie 2.0.6
U-Boot code: 06000000 -> 0607FFF0 BSS: -> 060D14C0
Soc: 88F6282 A1CPU running @ 2000Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 20 tRCD=8
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 98M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (98M - 97M): Done
NAND:256 MB
*** Warning - bad CRC or NAND, using default environment
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.
SCSI: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: 64bit ncq pm led clo pmp pio slum part
scanning bus for devices...
Invaild port number 2
Invaild port number 3
Net: egiga0 [PRIME]
egiga0 no link
Waiting for LUMP (3)
no lump receive; continuing
Hit any key to stop autoboot: 0
Reset IDE:
Marvell Serial ATA Adapter
Marvell Serial ATA Adapter
Integrated Sata device found
PCIe SATA:ffffffff
Booting Nexus layout from disk 0...
** Bad partition 3 **
Booting Nexus layout from disk 1...
** Bad partition 3 **
Booting Nexus rescue from NAND...
Loading from NAND 256MB 3,3V 8-bit, offset 0x100000
Reading data from 0x100000 -- 100% complete.
Image Name: Linux-2.6.31.14-svn7170
Created: 2012-04-06 17:10:52 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8755908 Bytes = 8.4 MB
Load Address: 00008000
Entry Point: 00008000
Reading data from 0x959800 -- 100% complete.
## Booting image at 00800000 ...
Image Name: Linux-2.6.31.14-svn7170
Created: 2012-04-06 17:10:52 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8755908 Bytes = 8.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
bootargs from environment variables : button=0 bootfail=1 console=ttyS0,115200 root=/dev/mtdblock2 cap=gpt,lba64
Starting kernel ...
Uncompressing Linux...................................................................................................................................................................................................................................................................................................................................................................... done, booting the kernel.
▒
_ ____ _
| | __ _ / ___(_) ___
| | / _V | | | |/ _ \
| |__ | (_| | |___| | __/
|____| \__,_|\____|_|\___|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: L2BIG_DDR3 REV: 1 LE
Hold front button - long : FAIL
U-Boot 1.1.4 (Mar 21 2012 - 11:02:55) Marvell version: 3.5.9 LaCie 2.0.6
U-Boot code: 06000000 -> 0607FFF0 BSS: -> 060D14C0
Soc: 88F6282 A1CPU running @ 2000Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 20 tRCD=8
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 98M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (98M - 97M): Done
NAND:256 MB
*** Warning - bad CRC or NAND, using default environment
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.
SCSI: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: 64bit ncq pm led clo pmp pio slum part
scanning bus for devices...
Invaild port number 2
Invaild port number 3
Net: egiga0 [PRIME]
egiga0 no link
Waiting for LUMP (3)
no lump receive; continuing
Hit any key to stop autoboot: 0
Reset IDE:
Marvell Serial ATA Adapter
Marvell Serial ATA Adapter
Integrated Sata device found
PCIe SATA:ffffffff
Booting Nexus layout from disk 0...
** Bad partition 3 **
Booting Nexus layout from disk 1...
** Bad partition 3 **
Booting Nexus rescue from NAND...
Loading from NAND 256MB 3,3V 8-bit, offset 0x100000
Reading data from 0x100000 -- 100% complete.
Image Name: Linux-2.6.31.14-svn7170
Created: 2012-04-06 17:10:52 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8755908 Bytes = 8.4 MB
Load Address: 00008000
Entry Point: 00008000
Reading data from 0x959800 -- 100% complete.
## Booting image at 00800000 ...
Image Name: Linux-2.6.31.14-svn7170
Created: 2012-04-06 17:10:52 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8755908 Bytes = 8.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
bootargs from environment variables : button=0 bootfail=1 console=ttyS0,115200 root=/dev/mtdblock2 cap=gpt,lba64
Starting kernel ...
Uncompressing Linux...................................................................................................................................................................................................................................................................................................................................................................... done, booting the kernel.
[ 0.000000] Linux version 2.6.31.14-svn7170 (root@sbs2_node0.lacie.com) (gcc version 4.4.1 (Sourcery G++ Lite 2010q1-202) ) #1 Fri Apr 6 17:10:41 UTC 2012
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: nas2big
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: button=0 bootfail=1 console=ttyS0,115200 root=/dev/mtdblock2 cap=gpt,lba64
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 248192KB available (10860K code, 370K data, 140K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000123] Console: colour dummy device 80x30
[ 0.000149] Calibrating delay loop... 1998.84 BogoMIPS (lpj=9994240)
[ 0.270102] Mount-cache hash table entries: 512
[ 0.270363] CPU: Testing write buffer coherency: ok
[ 0.271960] NET: Registered protocol family 16
[ 0.273863] Feroceon L2: Enabling L2
[ 0.273896] Feroceon L2: Cache support initialised.
[ 0.274261]
[ 0.274264] CPU Interface
[ 0.274267] -------------
[ 0.274271] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.274279] SDRAM_CS1 ....disable
[ 0.274283] SDRAM_CS2 ....disable
[ 0.274288] SDRAM_CS3 ....disable
[ 0.274292] PEX0_MEM ....base e8000000, size 128MB
[ 0.274300] PEX0_IO ....base f2000000, size 1MB
[ 0.274307] INTER_REGS ....base f1000000, size 1MB
[ 0.274314] NFLASH_CS ....base fa000000, size 2MB
[ 0.274322] SPI_CS ....base f4000000, size 16MB
[ 0.274331] BOOT_ROM_CS ....no such
[ 0.274343] DEV_BOOTCS ....no such
[ 0.274355] CRYPT_ENG ....base f0000000, size 2MB
[ 0.274367]
[ 0.274369] Marvell Development Board (LSP Version KW_LSP_5.0.3)-- net2big_v2 Soc: MV88F1155 Rev 1 LE
[ 0.274380]
[ 0.274383] Detected Tclk 200000000 and SysClk 500000000
[ 0.275530] Register Marvell USB EHCI Host controller #0
[ 0.276275] Kirkwood PCIe port 0:
[ 0.276280] link up
[ 0.276283] Kirkwood PCIe port 1:
[ 0.276287] link down, ignoring
[ 0.276291] PCI: bus0 uses PCIe port 0
[ 0.276591] pci 0000:00:01.0: PME# supported from D3hot
[ 0.276599] pci 0000:00:01.0: PME# disabled
[ 0.276630] PCI: bus0: Fast back to back transfers disabled
[ 0.282669] bio: create slab <bio-0> at 0
[ 0.282942] SCSI Scattered Spinup: Enabled
[ 0.282948] o Maximum Disk Spinup: 1
[ 0.282952] o Disk Spinup timeout: 10
[ 0.283335] SCSI subsystem initialized
[ 0.284963] NET: Registered protocol family 2
[ 0.285040] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.285207] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.285401] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.285500] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.285506] TCP reno registered
[ 0.285572] NET: Registered protocol family 1
[ 0.290044] Switched to NOHz mode on CPU #0
[ 0.537733] cpufreq: Init kirkwood cpufreq driver
[ 0.538275] gpio-hd-power gpio-hd-power: GPIO Hard Disk power device initialized
[ 0.538386] gpio-usb gpio-usb: USB GPIO's initialized
[ 0.539732] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.539750] Registering unionfs 2.5.10 (for 2.6.31.14)
[ 0.539947] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.540634] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.540980] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[ 0.541304] SGI XFS Quota Management subsystem
[ 0.541327] msgmni has been set to 485
[ 0.541414] alg: No test for cipher_null (cipher_null-generic)
[ 0.541461] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[ 0.541504] alg: No test for digest_null (digest_null-generic)
[ 0.541547] alg: No test for compress_null (compress_null-generic)
[ 0.546686] alg: No test for stdrng (krng)
[ 0.607251] alg: No test for hmac(digest_null) (hmac(digest_null-generic))
[ 0.635809] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.635820] io scheduler noop registered
[ 0.635824] io scheduler anticipatory registered (default)
[ 0.635829] io scheduler deadline registered
[ 0.635864] io scheduler cfq registered
[ 0.646306] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.647039] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.647058] console [ttyS0] enabled
[ 1.090837] brd: module loaded
[ 1.094342] sata_mv sata_mv.0: version 1.28
[ 1.098662] sata_mv sata_mv.0: slots 32 ports 2
[ 1.103694] scsi0 : sata_mv
[ 1.106806] scsi1 : sata_mv
[ 1.109802] ata1: SATA max UDMA/133 irq 21
[ 1.113952] ata2: SATA max UDMA/133 irq 21
[ 1.118247] PCI: enabling device 0000:00:01.0 (0146 -> 0147)
[ 1.124021] ahci 0000:00:01.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
[ 1.132163] ahci 0000:00:01.0: flags: 64bit ncq pm led clo pmp pio slum part
[ 1.139759] scsi2 : ahci
[ 1.142548] ata3: SATA max UDMA/133 abar m512@0xe0010000 port 0xe0010100 irq 9
[ 1.149949] INIT Marvell Ethernet Driver: mv_netdev
[ 1.155034] Loading Marvell Ethernet Driver:
[ 1.159321] o Cached descriptors in DRAM
[ 1.163447] o DRAM SW cache-coherency
[ 1.167298] o 2 Giga ports supported
[ 1.171063] o Single RX Queue support - ETH_DEF_RXQ=0
[ 1.176305] o Single TX Queue support - ETH_DEF_TXQ=0
[ 1.181551] o TCP segmentation offload (TSO) supported
[ 1.186883] o Large Receive offload (LRO) supported
[ 1.191953] o Receive checksum offload supported
[ 1.196762] o Transmit checksum offload supported
[ 1.201659] o Network Fast Processing (Routing) supported - (Disabled)
[ 1.208386] o Proc tool API enabled
[ 1.212062] o SKB Reuse supported - (Disabled)
[ 1.216696] o SKB Recycle supported - (Disabled)
[ 1.221505] o Rx descripors: q0=128
[ 1.225198] o Tx descripors: q0=532
[ 1.228889] o Loading network interface(s):
[ 1.234205] o register under mv_netdev platform
[ 1.239724] o eth0, ifindex = 2, GbE port = 0
[ 1.244475]
[ 1.244477] Warning: Giga 1 is Powered Off
[ 1.250081]
[ 1.251592] mvFpRuleDb (ce58a000): 2048 entries, 8192 bytes
[ 1.257326] console [netcon0] enabled
[ 1.261018] netconsole: network logging started
[ 1.266164] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
[ 1.274752] Scanning device for bad blocks
[ 1.405123] Creating 4 MTD partitions on "orion_nand":
[ 1.410291] 0x000000000000-0x000000100000 : "u-boot"
[ 1.415832] 0x000000100000-0x000001100000 : "uImage"
[ 1.421244] 0x000001100000-0x000009100000 : "root"
[ 1.426515] 0x000009100000-0x000010000000 : "unused"
[ 1.432549] mice: PS/2 mouse device common for all mice
[ 1.438014] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 1.445538] at24 0-0050: 512 byte 24c04 EEPROM (writable)
[ 1.452774] rtc-ds1307 0-0068: rtc core: registered ds1337 as rtc0
[ 1.459275] g762 0-003e: device successfully initialized
[ 1.464837] gpio-fan gpio-fan: GPIO fan initialized
[ 1.470473] cpuidle: using governor ladder
[ 1.474845] cpuidle: using governor menu
[ 1.479062] Registered led device: net2big-v2:blue:power
[ 1.484516] Registered led device: net2big-v2:red:power
[ 1.489853] Registered led device: net2big-v2:blue:sata0
[ 1.495315] Registered led device: net2big-v2:red:sata0
[ 1.500679] Registered led device: net2big-v2:blue:sata1
[ 1.506103] Registered led device: net2big-v2:red:sata1
[ 1.511464] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[ 1.517876] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[ 1.530050] ata1: SATA link down (SStatus 0 SControl F300)
[ 1.560052] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.565500] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 1.610046] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 1.650044] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[ 1.690045] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[ 1.695911] TCP cubic registered
[ 1.699150] NET: Registered protocol family 17
[ 1.703681] Bridge firewalling registered
[ 1.707707] NET: Registered protocol family 5
[ 1.712243] RPC: Registered udp transport module.
[ 1.716963] RPC: Registered tcp transport module.
[ 1.723284] rtc-ds1307 0-0068: setting system clock to 2020-11-07 13:14:34 UTC (1604754874)
[ 1.880040] ata2: SATA link down (SStatus 0 SControl F300)
[ 1.885586] Freeing init memory: 140K
[ 1.889643] Freeing initramfs memory: 5872K
init started: BusyBox v1.19.2 (2012-04-06 16:52:36 UTC)
==== Initializing system base
______ _____ _____ _____ _ _ _____
| ___ \ ___/ ___/ __ \ | | | ___|
| |_/ / |__ \ `--.| / \/ | | | |__
| /| __| `--. \ | | | | | __|
| |\ \| |___/\__/ / \__/\ |_| | |___
\_| \_\____/\____/ \____/\___/\____/
/sbin/gen-api-xml: line 28: can't create /www/api/external/system_info: nonexistent directory
Starting 'S00modules'... [ 2.182386] md: linear personality registered for level -1
[ 2.199691] md: raid0 personality registered for level 0
[ 2.219832] md: raid1 personality registered for level 1
[ 2.239786] md: raid10 personality registered for level 10
[ 2.420212] raid6: int32x1 123 MB/s
[ 2.590204] raid6: int32x2 170 MB/s
[ 2.760077] raid6: int32x4 192 MB/s
[ 2.930223] raid6: int32x8 224 MB/s
[ 2.933988] raid6: using algorithm int32x8 (224 MB/s)
[ 2.942241] xor: measuring software checksum speed
[ 2.990027] arm4regs : 1819.200 MB/sec
[ 3.040028] 8regs : 1091.600 MB/sec
[ 3.090027] 32regs : 1409.200 MB/sec
[ 3.094227] xor: using function: arm4regs (1819.200 MB/sec)
[ 3.103985] async_tx: api initialized (async)
[ 3.126407] md: raid6 personality registered for level 6
[ 3.131795] md: raid5 personality registered for level 5
[ 3.137129] md: raid4 personality registered for level 4
OK
Starting 'S20buttons-manager'... OK
Starting 'S30klaxon'... OK
Starting 'S70klaxon_env'... OK
Starting 'S80driveplug'... OK
Please press Enter to activate this console.
BusyBox v1.19.2 (2012-04-06 16:52:36 UTC) built-in shell (ash)
Enter 'help' for a list of built-in commands.
Hi there,
You are now in the Rescue.
If you want to :
1/ Reset your counter, invoke "reset_boot_count"
sh: rescue.jeeves.bootfrom: unknown operand
2/ Repair your product (will erase both rootfs bank), invoke "update "
3/ Wipe your drive (will totally wipe the drive), invoke "wipe "
4/ Mount the user data, invoke "mount_user_data mount"
Then reboot your product.
NASRescue / #lien configuration : https://wikidevi.wi-cat.ru/LaCie_2Big_NAS
merci d'avance
